Align T-REX 500 PRO DFC Super Combo Helicoper Kit w/Motor, ESC, 4 Ser

This is the Align T-REX 500 PRO DFC Flybarless Super Combo Helicopter Set. This incredible plan consists of not only the T-REX 500 PRO Set, however likewise a 425 3G Carbon Fiber blade set, a 500MX Brushless motor, a RCE-BL70G Brushless Electronic Speed Controller, three DS515M cyclic servos, one DS525M tail servo and finally the fantastic 3GX Programmable Flybarless System. This very combination supplies you with an amazing helicopter kit and an equally impressive electronic plan all in one box.

T-REX 500 PRO Includes: The Align 500 PRO DFC helicopter is geared up with an extremely low CG design to effectively lower wind resistance during flight and offer the most direct and precise control feel back to the pilot, offering exciting 3D efficiency and inconceivable flight speed.
A uniquely carbon composite technology effectively reinforce the weak locations and provides simplified electronics setup.
The servos can be mounted directly onto the frame without mounting nuts.
The rear servo is mounted in-frame for a centralized design and optimal 3D efficiency.
MX series high effectiveness brushless motor consisted of with heatsink style housing and ingrained fan to significantly enhance cooling and increase power output.
Distinct quick release gyro and receiver install design for quick removal and sturdy attachment.
High precision slant tooth (helical) primary equipment for higher load sustainability and lower noise output.
Redesigned tail gear box with higher material quality and easy upkeep.
High quality tail gearbox design, combined with upgraded double point mounted tail pitch control assembly to minimize slop and increase rudder control precision.
Extremely effective shaft driven tail system which effectively lower power loss found on belt driven systems. This likewise increases efficiency during flight.
Redesigned 4mm carbon rudder control rod and metal rudder pitch bell crank to more enhance the rudder locking result and controllability.
Redesigned style battery mounting platform to reinforce the frame in addition to to offer a mount for the electronic speed controller.
Redesigned lower CG landing equipment style.
Styled aerodynamically canopy for the supreme fit, making the helicopter stick out.
Finest tail equipment ratio to minimize vibrations caused by the high speed operations of the primary blades, bringing the best tail locking power.

3GX Programmable Flybarless System Includes:

Redesigned 3GX represents the next generation of multi function flybarless systems. The significantly enhanced efficiency will create an instant effect on any lovers.
The 3GX is presently the tiniest and lightest flybarless system on the market and includes 2 ports to directly connect Spektrum and JR satellite receivers, in addition to full assistance of Futaba's S-BUS system.
Using the 3G FL760 manual setup process, the 3GX can be setup just in a matter of minutes. In addition, the 3GX can support any CCPM swashplate system presently on the market consisting of 90, 120, 135, and 140 degree swashplates.
Graphically illustrated instructions using the computer setup software application directs the user through an action by step setup process, enabling fast setups without leaving out any steps.
With the quickly to be launched Bluetooth connectivity kit, the 3GX can be set wirelessly from a PC. Ultimately there will likewise be smartphone apps allowing live changes to the 3GX without powering down.
With 3GX's integrated in Align RCE-G600 governor function, no external governor is required, lowering electronic mess and excess wire.
A library of pre-configured 3GX settings are readily available for T-Rex series of helicopters, allowing pilots to achieve the most optimal setup for their helicopter without the uncertainty.
Three levels of flight mode are readily available to offer the best feel for beginner and advanced pilots.
Custom parameters have been developed to allow pilots to tweak numerous swashplate and rudder settings and a settings export feature enables custom-made settings to be shared amongst buddies.
The 3GX includes the highest spec gyroscope sensors, allowing it to be utilized in the harshest conditions. The double axis plus rudder sensing unit significantly improves swashplate and rudder correction precision and will be felt when hovering, in addition to during aerobatic routines.
Appropriate for 200 to 700 class helicopters, radiance engine or electrical powered.
The vibration resistant characteristics are evident even when mounted with harder double sided mounting tape.
16 bit processor is 4 times faster than the previous 3G, in addition to entirely re-written firmware. The outcome is a dramatic improvement in stability that measures up to a flybarred helicopter, while offering explosive dexterity.
With a built in pirouette payment function, the 3GX is able to support the helicopter on a set point during pirouetting maneuvers. Pirouetting flip type of maneuvers are easily carried out with precision.
Rudder control is similar to the high end GP-780 gyro because the rudder sensitivity is optimized for the helicopter's rudder response characteristics, allowing constant rudder feel even under high speed conditions. This outstanding control feel will allow pilots of all ability levels to experience the best integration in between the 3GX and the helicopter.
Extra peripherals planned for the 3GX include a 3-axis accelerometer, 3-axis magnetic compass, and a GPS placing system.
The position hold gyro system utilizes a total of 10 sensors, make sure positioning of the helicopter with exceptional accuracy and offering the supreme solution for aerial photography and other specialized applications.
Compatible with 2 to 5 blades rotor heads
Support as much as 6 servos
Automatic servo type acknowledgment

T-REX 500 PRO Specifications:

Length: 868mm

Height: 275mm

Main Blade Length: 425mm

Main Rotor Diameter: 978mm

Tail Rotor Diameter: 206mm

Motor Drive Equipment: 12T

Main Drive Equipment: 134T

Autorotation Tail Drive Equipment: 145T

Tail Drive Equipment: 36T

Drive Equipment Ratio: 1:11.17:4.03

Weight (With Motor): 1210g

3GX Specifications:

Operating Temperature: -10~60 degree

X and Y axis Operating Angle Variety: -300~+300 degree

Z axis Operating Angle Variety: -600~+600 degree

Size: 36.5x25.2x15.6mm

Weight: 11g

Maximum working voltage: 8.5V 

Consists of: (1) T-REX 500 PRO DFC Set
(1) 3GX Flybarless System


(1) 425 3G Carbon Fiber blades


(1) 500MX Brushless Motor (1600kV)
(3) DS515M Digital servo


(1) DS525M Digital servo


(1) RCE-BL70G Brushless ESC 

Required to Total:


Transmitter (7-channel or more, helicopter system)
Receiver (7-channel or more)
6S LiPo Battery Pack 2600 ~ 4600mAh (3300mAh advised)
Digital Pitch Gauge