Align T-REX 500 PRO DFC Super Combo Helicoper Kit w/Motor, ESC, 4 Ser

This is the Align T-REX 500 PRO DFC Flybarless Super Combo Helicopter Package. This amazing plan includes not only the T-REX 500 PRO Package, but likewise a 425 3G Carbon Fiber blade set, a 500MX Brushless motor, a RCE-BL70G Brushless Electronic Speed Controller, three DS515M cyclic servos, one DS525M tail servo and finally the fantastic 3GX Programmable Flybarless System. This extremely combo offers you with an unbelievable helicopter kit and an equally outstanding electronic plan all in one box.

T-REX 500 PRO Includes: The Align 500 PRO DFC helicopter is equipped with an exceptionally low CG design to successfully decrease wind resistance during flight and provide the most direct and accurate control feel back to the pilot, supplying exhilarating 3D efficiency and unthinkable flight speed.
A uniquely carbon composite technology successfully enhance the weak areas and offers simplified electronic devices installation.
The servos can be installed straight onto the frame without installing nuts.
The rear servo is installed in-frame for a centralized design and ideal 3D efficiency.
MX series high effectiveness brushless motor included with heatsink style casing and ingrained fan to considerably enhance cooling and increase power output.
Special quick release gyro and receiver install design for quick elimination and tough attachment.
High accuracy slant tooth (helical) primary equipment for higher load sustainability and lower sound output.
Redesigned tail gear box with higher material quality and simple upkeep.
High quality tail transmission design, integrated with updated dual point installed tail pitch control assembly to decrease slop and increase rudder control accuracy.
Highly effective shaft driven tail system which successfully decrease power loss discovered on belt driven systems. This likewise increases efficiency during flight.
Redesigned 4mm carbon rudder control rod and metal rudder pitch bell crank to further enhance the rudder locking effect and controllability.
Redesigned style battery installing platform to enhance the frame in addition to to provide a mount for the electronic speed controller.
Redesigned lower CG landing equipment style.
Styled aerodynamically canopy for the ultimate fit, making the helicopter stick out.
Finest tail equipment ratio to decrease vibrations caused by the high speed operations of the primary blades, bringing the very best tail locking power.

3GX Programmable Flybarless System Includes:

Redesigned 3GX represents the next generation of multi function flybarless systems. The considerably improved efficiency will develop an instant influence on any enthusiasts.
The 3GX is currently the smallest and lightest flybarless system on the market and includes 2 ports to straight link Spektrum and JR satellite receivers, together with full assistance of Futaba's S-BUS system.
Utilizing the 3G FL760 manual setup procedure, the 3GX can be setup simply in a matter of minutes. Furthermore, the 3GX can support any CCPM swashplate system currently on the market including 90, 120, 135, and 140 degree swashplates.
Graphically detailed directions using the computer setup software application directs the user as a result of a step by action setup procedure, enabling fast setups without leaving out any actions.
With the quickly to be released Bluetooth connectivity kit, the 3GX can be set wirelessly from a PC. Eventually there will likewise be smartphone apps permitting live adjustments to the 3GX without powering down.
With 3GX's integrated in Align RCE-G600 guv function, no external guv is required, lowering electronic mess and excess wire.
A library of pre-configured 3GX settings are available for T-Rex series of helicopters, permitting pilots to attain the most ideal setup for their helicopter without the guesswork.
3 levels of flight mode are available to provide the best feel for beginner and advanced pilots.
Custom criteria have actually been established to enable pilots to fine tune many swashplate and rudder settings and a settings export feature enables custom settings to be shared among friends.
The 3GX includes the greatest spec gyroscope sensing units, permitting it to be used in the harshest conditions. The dual axis plus rudder sensing unit considerably enhances swashplate and rudder correction accuracy and will be felt when hovering, in addition to during aerobatic routines.
Appropriate for 200 to 700 class helicopters, radiance engine or electrical powered.
The vibration resistant characteristics appear even when installed with more difficult double sided installing tape.
16 bit processor is 4 times faster than the previous 3G, together with totally re-written firmware. The result is a remarkable enhancement in stability that measures up to a flybarred helicopter, while supplying explosive dexterity.
With a built in pirouette compensation function, the 3GX is able to stabilize the helicopter on a set point during pirouetting maneuvers. Pirouetting flip type of maneuvers are quickly performed with accuracy.
Rudder control is similar to the high end GP-780 gyro because the rudder level of sensitivity is optimized for the helicopter's rudder action characteristics, permitting consistent rudder feel even under high speed conditions. This outstanding control feel will enable pilots of all skill levels to experience the best combination in between the 3GX and the helicopter.
Extra peripherals prepared for the 3GX include a 3-axis accelerometer, 3-axis magnetic compass, and a GPS placing system.
The position hold gyro system makes use of a total of 10 sensing units, guarantee positioning of the helicopter with superior precision and supplying the ultimate solution for aerial photography and other specialized applications.
Compatible with 2 to 5 blades rotor heads
Assistance up to 6 servos
Automatic servo type acknowledgment

T-REX 500 PRO Specifications:

Length: 868mm

Height: 275mm

Main Blade Length: 425mm

Main Rotor Diameter: 978mm

Tail Rotor Diameter: 206mm

Motor Drive Gear: 12T

Main Drive Gear: 134T

Autorotation Tail Drive Gear: 145T

Tail Drive Gear: 36T

Drive Gear Ratio: 1:11.17:4.03

Weight (With Motor): 1210g

3GX Specifications:

Operating Temperature: -10~60 degree

X and Y axis Operating Angle Variety: -300~+300 degree

Z axis Operating Angle Variety: -600~+600 degree

Size: 36.5x25.2x15.6mm

Weight: 11g

Optimum working voltage: 8.5V 

Includes: (1) T-REX 500 PRO DFC Package
(1) 3GX Flybarless System


(1) 425 3G Carbon Fiber blades


(1) 500MX Brushless Motor (1600kV)
(3) DS515M Digital servo


(1) DS525M Digital servo


(1) RCE-BL70G Brushless ESC 

Required to Complete:


Transmitter (7-channel or more, helicopter system)
Receiver (7-channel or more)
SIX LiPo Battery Pack 2600 ~ 4600mAh (3300mAh suggested)
Digital Pitch Gauge