Align T-REX 500 PRO DFC Super Combo Helicoper Kit w/Motor, ESC, 4 Ser

This is the Align T-REX 500 PRO DFC Flybarless Super Combo Helicopter Kit. This amazing plan consists of not only the T-REX 500 PRO Kit, however likewise a 425 3G Carbon Fiber blade set, a 500MX Brushless motor, a RCE-BL70G Brushless Electronic Speed Controller, 3 DS515M cyclic servos, one DS525M tail servo and finally the fantastic 3GX Programmable Flybarless System. This extremely combo provides you with an unbelievable helicopter package and an equally remarkable electronic plan all in one box.

T-REX 500 PRO Includes: The Align 500 PRO DFC helicopter is geared up with a very low CG design to successfully minimize wind resistance during flight and provide the most direct and exact control feel back to the pilot, providing exciting 3D performance and unimaginable flight speed.
A uniquely carbon composite innovation successfully reinforce the weak locations and provides streamlined electronics installation.
The servos can be mounted directly onto the frame without mounting nuts.
The rear servo is mounted in-frame for a centralized design and optimal 3D performance.
MX series high efficiency brushless motor included with heatsink design housing and embedded fan to significantly improve cooling and boost power output.
Distinct quick release gyro and receiver install design for quick elimination and tough attachment.
High accuracy slant tooth (helical) main gear for greater load sustainability and lower sound output.
Redesigned tail gear box with greater material quality and simple maintenance.
High quality tail transmission design, combined with upgraded dual point mounted tail pitch control assembly to lessen slop and boost rudder control accuracy.
Highly effective shaft driven tail system which successfully minimize power loss found on belt driven systems. This likewise increases performance during flight.
Redesigned 4mm carbon rudder control rod and metal rudder pitch bell crank to more improve the rudder locking result and controllability.
Redesigned design battery mounting platform to reinforce the frame as well as to provide a mount for the electronic speed controller.
Redesigned lower CG landing gear design.
Styled aerodynamically canopy for the ultimate fit, making the helicopter stand apart.
Best tail gear ratio to lessen vibrations brought on by the high speed operations of the main blades, bringing the very best tail locking power.

3GX Programmable Flybarless System Includes:

Redesigned 3GX represents the next generation of multi function flybarless systems. The significantly improved performance will develop an instant influence on any lovers.
The 3GX is currently the tiniest and lightest flybarless system on the market and includes 2 ports to directly connect Spektrum and JR satellite receivers, along with full support of Futaba's S-BUS system.
Using the 3G FL760 manual setup procedure, the 3GX can be setup just in a matter of minutes. In addition, the 3GX can support any CCPM swashplate system currently on the market consisting of 90, 120, 135, and 140 degree swashplates.
Graphically detailed instructions utilizing the computer setup software application directs the user as a result of a step by step setup procedure, enabling fast setups without leaving out any actions.
With the soon to be released Bluetooth connectivity package, the 3GX can be configured wirelessly from a PC. Eventually there will likewise be smartphone apps permitting live changes to the 3GX without powering down.
With 3GX's built in Align RCE-G600 governor function, no external governor is needed, decreasing electronic mess and excess wire.
A library of pre-configured 3GX settings are readily available for T-Rex series of helicopters, permitting pilots to attain the most optimal setup for their helicopter without the guesswork.
Three levels of flight mode are readily available to provide the perfect feel for novice and advanced pilots.
Custom parameters have been developed to permit pilots to fine tune various swashplate and rudder settings and a settings export feature permits customized settings to be shared among good friends.
The 3GX includes the highest spec gyroscope sensors, permitting it to be utilized in the harshest conditions. The dual axis plus rudder sensor significantly enhances swashplate and rudder correction accuracy and will be felt when hovering, as well as during aerobatic routines.
Appropriate for 200 to 700 class helicopters, glow engine or electrical powered.
The vibration resistant qualities appear even when mounted with harder double sided mounting tape.
16 bit processor is 4 times faster than the previous 3G, along with entirely re-written firmware. The outcome is a remarkable improvement in stability that equals a flybarred helicopter, while providing explosive dexterity.
With an integrated in pirouette compensation function, the 3GX is able to support the helicopter on a fixed point during pirouetting maneuvers. Pirouetting flip type of maneuvers are quickly performed with accuracy.
Rudder control is similar to the high-end GP-780 gyro in that the rudder level of sensitivity is optimized for the helicopter's rudder response qualities, permitting consistent rudder feel even under high speed conditions. This outstanding control feel will permit pilots of all skill levels to experience the perfect integration between the 3GX and the helicopter.
Extra peripherals prepared for the 3GX include a 3-axis accelerometer, 3-axis magnetic compass, and a GPS positioning system.
The position hold gyro system utilizes a total of 10 sensors, ensure positioning of the helicopter with exceptional accuracy and providing the ultimate solution for aerial photography and other specialized applications.
Compatible with 2 to 5 blades rotor heads
Support approximately 6 servos
Automatic servo type acknowledgment

T-REX 500 PRO Specifications:

Length: 868mm

Height: 275mm

Main Blade Length: 425mm

Main Rotor Size: 978mm

Tail Rotor Size: 206mm

Motor Drive Gear: 12T

Main Drive Gear: 134T

Autorotation Tail Drive Gear: 145T

Tail Drive Gear: 36T

Drive Gear Ratio: 1:11.17:4.03

Weight (With Motor): 1210g

3GX Specifications:

Operating Temperature: -10~60 degree

X and Y axis Operating Angle Range: -300~+300 degree

Z axis Operating Angle Range: -600~+600 degree

Size: 36.5x25.2x15.6mm

Weight: 11g

Maximum working voltage: 8.5V 

Consists of: (1) T-REX 500 PRO DFC Kit
(1) 3GX Flybarless System


(1) 425 3G Carbon Fiber blades


(1) 500MX Brushless Motor (1600kV)
(3) DS515M Digital servo


(1) DS525M Digital servo


(1) RCE-BL70G Brushless ESC 

Needed to Complete:


Transmitter (7-channel or more, helicopter system)
Receiver (7-channel or more)
SIX LiPo Battery Load 2600 ~ 4600mAh (3300mAh suggested)
Digital Pitch Gauge