Align T-REX 470LP Super Combo

Following the release of the T-REX 450L, which introduced an ingenious style and came geared up with high-end electronic equipment. Align's most expected helicopter release in 2016 the T-REX 470L is born. No matter whether you are a newcomer or an expert, the brand name brand-new T-REX 470L will provide you the brand-new flying feel again.

470EFL Main Rotor Head supplies exceptional flight stability and uses a lower CG style to reduce flying resistance while providing a more stiff and fast rotor head reaction. To improve the strength and resilience of the main and feathering shaft the 470 main shaft outer dimension was increased from Ø5mm to Ø6mm, while the feathering shaft outer dimension was increased from Ø4mm to Ø5mm. The 470L has embrace a high basic 1.2mm 3K carbon fiber main frame and a larger body style which increases the size of the battery compartment allowing the usage of larger capacity battery. The 470L makes use of a high effective belt drive assembly style with an ingenious adjustable belt guide wheel, providing a hassle-free method to adjust the belt stress by launching or tightening up the screw. This screw is used to maintain ideal belt stress enhancing the life of the belt and lowering maintains costs. The landing skid is slanted 5 degrees forward to improve crashworthiness and makes T-REX470L more avant-garde and dynamic.

The T-REX 470L is geared up with the big outer size 470MX motor(1800KV/2818) which is extremely effective providing exceptional power, excellent torque, improved current draw, and a lower operating temperature level which are excellent enhancements as compared to the 460MX motor. The brand name brand-new DS450 digital cyclic servos and DS455 digital tail servo, support approximately V8.4, high voltage input, enhancing the servos torque and speed. The brand-new RCE-BL50X brushless ESC with an internal BEC supplies 5.0V to 8.4V which can be set based on servo spec. The brand-new high-end electronics effectively enhance flight performance.

Extended 380mm main blades effectively improve the flying stability and power efficiency. The brand-new crafted airfoil style effectively lowers turbulence at the end of the main blades,this conserves power consumption during severe 3D flight. New 69 size tail blades are longer in length and deal exceptional tail holding efficiency, even during requiring 3D flight.

Brand New 470EFL Main Rotor Head supplies exceptional flight stability and uses a lower CG style to reduce flying resistance while providing a more stiff and fast rotor head reaction. Brand New 470 Main Shaft and Feathering Shaft: Main Shaft outer dimension increased from Ø5mm to Ø6mm, while the Feathering Shaft outer dimension increased from Ø4mm to Ø5mm,effectively reinforcing the Main and Feathering Shaft while enhancing durability.

New 470MX motor features; high effectiveness, exceptional power, excellent torque, low current draw, and a low operating temperature level. The 470MX can preserving constant torque and head speed through constant 3D maneuvers. 470MX motor is designed for 3D flight.

New Swashplate style with absolutely no slop delivering an exact and accurate regulated flight.

>Manufactured using the current composite technology to embed brass inserts into main shaft bearing block, which enhance the structure integrety and strength. You can feel the solid structure even in severe 3D flight.

Carbon fiber side frame plates are produced using a proprietary composite product integration technology which incorporates the battery installing rails into the frame. This special usage of open areas within the frame develops a stiff frame and is visually pleasing.

An additional 3rd main shaft bearing block increases the strength of the main frame while enhancing 3D flight.

Brand brand-new latching battery tray which makes use of integrated installing rails inside the frames to streamline insertion / removal of battery while providing protection for the battery.

Specially designed for T-REX 470 providing higher currency output and assistance for high voltage servos with an internal BEC output from 5V to 8.4V which can be established based on servo specification.

DS350M HV Cyclic and DS455 HV Rudder servos support approximately 8.4V for exceptional responsiveness, severe torque, and improved performance.

Innovative adjustable belt guide wheel, enables a hassle-free method to adjust the belt stress by launching or tightening up the screw. The screw is used to maintain ideal belt stress over time.

The One Way Bearing is produced using bearing steal and after heat treatment the solidity is HRC50-55. This larger bearing has a greater load carry capacity which lowers the loss of momentum and improves the fficiency, speed, and smoothness of the main rotor. The brand-new main equipment case and all-metal central wheel transmission system is an effective style to provide the ultimate performance.

Landing skid is slanted 5 degrees forward to improve crashworthiness.

Newly designed vertical tail servo mount to improve CG while increasing the responsiveness of 3D flight.

A wider Tail Boom to improves the torsional strength.

Designed using a proprietary product integration technology which develops a unique appearance and improves the Vertical Stabilizer's stiffness.

The freshly designed dual point supported tail control assembly provides slop complimentary efficiency while enhancing rudder resolution and precision.

The brand-new tail rotor holder style includes thrust bearings which increases resilience, along with substantially enhancing the precision and effectiveness of the tail efficiency when using 69 size Tail Blades.

 Basic equipment

.Microbeast PLUS Flybarless System X 1
.RCE-BL50X 50A Brushless ESC X 1
.470MX Brushless Motor(1800KV/2818) X 1
.DS450 Digital Servo X 3
.DS455 Digital Servo X 1

Specification:
.Length: 755mm
.Height: 210mm
.Width: 108mm
.Main Blade Length: 380mm
.Main Rotor Size: 850mm
.Tail Rotor Size: 181mm
.Motor Pinion Gear: 11T
.Main Drive Gear: 121T
.Main Drive Wheel: 56T
.Tail Drive Gear: 15T
.Drive Gear Ratio: 11:1:3.73
.Weight(w/o battery): 840gAccessories

.T-REX 470L BOSS Set x 1
.380 Carbon Fiber Blades x 1set
.69 Tail Blade x 1set
.470MX Brushless Motor(1800KV/2818) x 1
.DS450 Digital Servo x 3
.DS455 Digital Servo x 1
.RCE-BL50X 50A Brushless ESC x 1

Radio transmitter and electronic equipment needed for assembly:
1.Transmitter(6-channel or more,helicopter system)
2.Receiver(6-channel or more)
3.Pitch gauge or Digital Pitch Gauge
4.6S Li-Po 1400~1900mAh battery x 1