Align T-REX 470LP Super Combo

Following the release of the T-REX 450L, which presented an ingenious style and came geared up with high-end electronic equipment. Align's a lot of expected helicopter release in 2016 the T-REX 470L is born. No matter whether you are a newbie or a professional, the brand brand-new T-REX 470L will give you the brand-new flying feel again.

470EFL Main Rotor Head provides remarkable flight stability and uses a lower CG style to reduce flying resistance while supplying a more stiff and quick rotor head reaction. To enhance the strength and toughness of the primary and feathering shaft the 470 primary shaft outer measurement was increased from Ø5mm to Ø6mm, while the feathering shaft outer measurement was increased from Ø4mm to Ø5mm. The 470L has adopt a high basic 1.2mm 3K carbon fiber primary frame and a wider body style which increases the size of the battery compartment allowing the use of larger capacity battery. The 470L utilizes a high efficient belt drive assembly style with an ingenious adjustable belt guide wheel, supplying a practical way to adjust the belt tension by launching or tightening up the screw. This screw is utilized to maintain optimal belt tension improving the life of the belt and reducing keeps expenses. The landing skid is tilted 5 degrees forward to enhance crashworthiness and makes T-REX470L more avant-garde and dynamic.

The T-REX 470L is geared up with the big outer size 470MX motor(1800KV/2818) which is extremely efficient supplying remarkable power, outstanding torque, enhanced current draw, and a lower operating temperature level which are outstanding enhancements as compared to the 460MX motor. The brand brand-new DS450 digital cyclic servos and DS455 digital tail servo, support as much as V8.4, high voltage input, improving the servos torque and speed. The brand-new RCE-BL50X brushless ESC with an internal BEC provides 5.0V to 8.4V which can be set based on servo spec. The brand-new high-end electronics effectively enhance flight performance.

Extended 380mm primary blades effectively enhance the flying stability and power efficiency. The brand-new crafted airfoil style effectively reduces turbulence at the end of the primary blades,this saves power consumption throughout severe 3D flight. New 69 size tail blades are longer in length and offer remarkable tail holding efficiency, even throughout demanding 3D flight.

Brand New 470EFL Main Rotor Head provides remarkable flight stability and uses a lower CG style to reduce flying resistance while supplying a more stiff and quick rotor head reaction. Brand New 470 Main Shaft and Feathering Shaft: Main Shaft outer measurement increased from Ø5mm to Ø6mm, while the Feathering Shaft outer measurement increased from Ø4mm to Ø5mm,effectively enhancing the Main and Feathering Shaft while improving durability.

New 470MX motor functions; high efficiency, remarkable power, outstanding torque, low current draw, and a low operating temperature level. The 470MX can preserving constant torque and head speed through continuous 3D maneuvers. 470MX motor is created for 3D flight.

New Swashplate style with no slop delivering an accurate and accurate regulated flight.

>Manufactured using the current composite technology to embed brass inserts into primary shaft bearing block, which enhance the structure integrety and strength. You can feel the strong structure even in severe 3D flight.

Carbon fiber side frame plates are manufactured using a proprietary composite material integration technology which integrates the battery installing rails into the frame. This distinct use of open areas within the frame creates a stiff frame and is aesthetically pleasing.

An extra 3rd primary shaft bearing block increases the strength of the primary frame while improving 3D flight.

Brand brand-new locking battery tray which utilizes integrated installing rails inside the frames to simplify insertion / removal of battery while supplying defense for the battery.

Specially created for T-REX 470 supplying greater currency output and assistance for high voltage servos with an internal BEC output from 5V to 8.4V which can be set up based on servo specification.

DS350M HV Cyclic and DS455 HV Rudder servos support as much as 8.4V for remarkable responsiveness, severe torque, and enhanced performance.

Innovative adjustable belt guide wheel, permits a practical way to adjust the belt tension by launching or tightening up the screw. The screw is utilized to maintain optimal belt tension over time.

The One Way Bearing is manufactured using bearing steal and after heat treatment the firmness is HRC50-55. This larger bearing has a greater load carry capacity which reduces the loss of momentum and enhances the fficiency, speed, and smoothness of the primary rotor. The brand-new primary equipment case and all-metal central wheel transmission system is an effective style to deliver the supreme performance.

Landing skid is tilted 5 degrees forward to enhance crashworthiness.

Newly created vertical tail servo mount to enhance CG while increasing the responsiveness of 3D flight.

A wider Tail Boom to enhances the torsional strength.

Designed using a proprietary material integration technology which creates a unique look and enhances the Vertical Stabilizer's stiffness.

The freshly created dual point supported tail control assembly delivers slop free efficiency while improving rudder resolution and precision.

The brand-new tail rotor holder style consists of thrust bearings which increases toughness, along with significantly improving the precision and efficiency of the tail efficiency when using 69 size Tail Blades.

 Standard equipment

.Microbeast PLUS Flybarless System X 1
.RCE-BL50X 50A Brushless ESC X 1
.470MX Brushless Motor(1800KV/2818) X 1
.DS450 Digital Servo X 3
.DS455 Digital Servo X 1

Spec:
.Length: 755mm
.Height: 210mm
.Width: 108mm
.Main Blade Length: 380mm
.Main Rotor Size: 850mm
.Tail Rotor Size: 181mm
.Motor Pinion Gear: 11T
.Main Drive Gear: 121T
.Main Drive Pulley: 56T
.Tail Drive Gear: 15T
.Drive Gear Ratio: 11:1:3.73
.Weight(w/o battery): 840gAccessories

.T-REX 470L DOMINATOR Set x 1
.380 Carbon Fiber Blades x 1set
.69 Tail Blade x 1set
.470MX Brushless Motor(1800KV/2818) x 1
.DS450 Digital Servo x 3
.DS455 Digital Servo x 1
.RCE-BL50X 50A Brushless ESC x 1

Radio transmitter and electronic equipment needed for assembly:
1.Transmitter(6-channel or more,helicopter system)
2.Receiver(6-channel or more)
3.Pitch gauge or Digital Pitch Gauge
4.6S Li-Po 1400~1900mAh battery x 1