Align T-REX 470LM KIT (w/ Motor and ESC)

Following the release of the T-REX 450L, which introduced an innovative design and came equipped with high-end electronic devices. Align's a lot of expected helicopter release in 2016 the T-REX 470L is born. No matter whether you are a beginner or a professional, the brand brand-new T-REX 470L will provide you the brand-new flying feel again.

470EFL Main Rotor Head provides remarkable flight stability and uses a lower CG design to reduce flying resistance while supplying a more rigid and quick rotor head response. To improve the strength and toughness of the primary and feathering shaft the 470 primary shaft external measurement was increased from Ø5mm to Ø6mm, while the feathering shaft external measurement was increased from Ø4mm to Ø5mm. The 470L has adopt a high basic 1.2mm 3K carbon fiber primary frame and a wider body design which increases the size of the battery compartment permitting the use of bigger capability battery. The 470L utilizes a high efficient belt drive assembly design with an innovative adjustable belt guide pulley-block, supplying a practical method to change the belt tension by releasing or tightening up the screw. This screw is utilized to maintain optimum belt tension enhancing the life of the belt and lowering maintains expenses. The landing skid is tilted 5 degrees forward to improve crashworthiness and makes T-REX470L more progressive and dynamic.

The T-REX 470L is equipped with the large external diameter 470MX motor (1800KV) which is extremely efficient supplying remarkable power, outstanding torque, enhanced present draw, and a lower operating temperature which are outstanding enhancements as compared with the 460MX motor.

Extended 380mm primary blades successfully improve the flying stability and power performance. The brand-new engineered airfoil design successfully lowers turbulence at the end of the primary blades,this conserves power intake throughout extreme 3D flight. New 69 size tail blades are longer in length and offer remarkable tail holding performance, even throughout requiring 3D flight.

Brand New 470EFL Main Rotor Head provides remarkable flight stability and uses a lower CG design to reduce flying resistance while supplying a more rigid and quick rotor head response. Brand name New 470 Main Shaft and Feathering Shaft: Main Shaft external measurement increased from Ø5mm to Ø6mm, while the Feathering Shaft external measurement increased from Ø4mm to Ø5mm,successfully reinforcing the Main and Feathering Shaft while enhancing durability.

New 470MX motor features; high effectiveness, remarkable power, outstanding torque, low present draw, and a low operating temperature. The 470MX can keeping consistent torque and head speed through continuous 3D maneuvers. 470MX motor is created for 3D flight.

New Swashplate design with absolutely no slop delivering an accurate and accurate controlled flight.

Brand brand-new CNC metal support plate and brace compare with frame mounting bolt successfully increase the torsional stength of primary frame, under extreme 3D maneuver, you can highly feel its solid support from its structure.

Carbon fiber side frame plates are produced using a proprietary composite product integration technology which incorporates the battery mounting rails into the frame. This distinct use of open spaces within the frame produces a stiff frame and is visually pleasing.

An additional 3rd primary shaft bearing block increases the strength of the primary frame while enhancing 3D flight.

Brand brand-new locking battery tray which utilizes integrated mounting rails inside the frames to streamline insertion / elimination of battery while supplying protection for the battery.

Specially created for T-REX 470 supplying higher currency output and assistance for high voltage servos with an internal BEC output from 5V to 8.4V which can be established based on servo specification.

DS350M HV Cyclic and DS455 HV Rudder servos support as much as 8.4V for remarkable responsiveness, extreme torque, and enhanced performance.

Innovative adjustable belt guide pulley-block, allows a practical method to change the belt tension by releasing or tightening up the screw. The screw is utilized to maintain optimum belt tension over time.

The One Way Bearing is produced using bearing take and after heat treatment the firmness is HRC50-55. This bigger bearing has a higher load bring capability which lowers the loss of momentum and enhances the fficiency, speed, and smoothness of the primary rotor. The brand-new primary equipment case and all-metal central pulley-block transmission system is an efficient design to deliver the supreme performance.

Landing skid is tilted 5 degrees forward to improve crashworthiness.

Newly created vertical tail servo mount to improve CG while increasing the responsiveness of 3D flight.

A broader Tail Boom to enhances the torsional strength. Carbon Fiber Tail Control Rod is practical and enhances the helicopters tail control.

Designed using a proprietary product integration technology which produces a unique appearance and enhances the Vertical Stabilizer's stiffness.

The recently created double point supported tail control assembly delivers slop complimentary performance while enhancing rudder resolution and precision.

The brand-new tail rotor holder design consists of thrust bearings which increases toughness, in addition to considerably enhancing the precision and effectiveness of the tail performance when using 69 size Tail Blades.

Standard devices

?RCE-BL50X 50A Brushless ESC X 1
?470MX Brushless Motor(1800KV) X 1

Requirements

?Length: 755mm
?Height: 210mm
?Width: 108mm
?Main Blade Length: 380mm
?Main Rotor Size: 850mm
?Tail Rotor Size: 181mm
?Motor Pinion Gear: 11T
?Main Drive Gear: 121T
?Main Drive Wheel: 56T
?Tail Own Gear: 15T
?Own Gear Ratio: 11:1:3.73
?Weight(w/o battery): 860gAccessories

?T-REX 470L DOMINATOR Set x 1
?380 Carbon Fiber Blades x 1set
?69 Tail Blade x1set
?470MX Brushless Motor(1800KV) x 1
?RCE-BL50X 50A Brushless ESC x 1

Radio transmitter and electronic devices needed for assembly:
1.Transmitter(6-channel or more,helicopter system)
2.Receiver(6-channel or more)
3.Pitch gauge or Digital Pitch Gauge
4.6S Li-Po 1400~1900mAh battery x 1
5.CCPM Servo X 3
6.Tail Servo X 1
7.Flybarless System x 1