Align T-REX 470LM KIT (w/ Motor and ESC)

Following the release of the T-REX 450L, which presented an innovative design and came geared up with high-end electronic equipment. Align's the majority of anticipated helicopter release in 2016 the T-REX 470L is born. No matter whether you are a beginner or an expert, the brand name new T-REX 470L will give you the new flying feel once again.

470EFL Main Rotor Head supplies remarkable flight stability and offers a lower CG design to decrease flying resistance while offering a more rigid and fast rotor head action. To improve the strength and sturdiness of the primary and feathering shaft the 470 primary shaft outer dimension was increased from Ø5mm to Ø6mm, while the feathering shaft outer dimension was increased from Ø4mm to Ø5mm. The 470L has embrace a high basic 1.2mm 3K carbon fiber primary frame and a wider body design which increases the size of the battery compartment allowing the usage of bigger capacity battery. The 470L utilizes a high efficient belt drive assembly design with an innovative adjustable belt guide wheel, offering a convenient method to change the belt tension by launching or tightening up the screw. This screw is used to preserve optimum belt tension improving the life of the belt and reducing preserves expenses. The landing skid is slanted 5 degrees forward to improve crashworthiness and makes T-REX470L more progressive and dynamic.

The T-REX 470L is geared up with the big outer size 470MX motor (1800KV) which is highly efficient offering remarkable power, outstanding torque, enhanced current draw, and a lower operating temperature level which are outstanding enhancements as compared with the 460MX motor.

Extended 380mm primary blades successfully improve the flying stability and power efficiency. The new crafted airfoil design successfully lowers turbulence at the end of the primary blades,this saves power intake throughout severe 3D flight. New 69 size tail blades are longer in length and deal remarkable tail holding efficiency, even throughout demanding 3D flight.

Brand New 470EFL Main Rotor Head supplies remarkable flight stability and offers a lower CG design to decrease flying resistance while offering a more rigid and fast rotor head action. Brand name New 470 Main Shaft and Feathering Shaft: Main Shaft outer dimension increased from Ø5mm to Ø6mm, while the Feathering Shaft outer dimension increased from Ø4mm to Ø5mm,successfully enhancing the Main and Feathering Shaft while improving durability.

New 470MX motor functions; high effectiveness, remarkable power, outstanding torque, low current draw, and a low operating temperature level. The 470MX is capable of maintaining constant torque and head speed through constant 3D maneuvers. 470MX motor is designed for 3D flight.

New Swashplate design with zero slop delivering a precise and precise regulated flight.

Brand new CNC metal support plate and brace compare to frame installing bolt successfully increase the torsional stength of primary frame, under severe 3D maneuver, you can highly feel its solid support from its structure.

Carbon fiber side frame plates are made utilizing a proprietary composite material integration innovation which incorporates the battery installing rails into the frame. This special usage of open areas within the frame develops a stiff frame and is aesthetically pleasing.

An additional 3rd primary shaft bearing block increases the strength of the primary frame while improving 3D flight.

Brand new latching battery tray which utilizes incorporated installing rails inside the frames to streamline insertion / removal of battery while offering defense for the battery.

Specially designed for T-REX 470 offering greater currency output and support for high voltage servos with an internal BEC output from 5V to 8.4V which can be set up based on servo specification.

DS350M HV Cyclic and DS455 HV Rudder servos support approximately 8.4V for remarkable responsiveness, severe torque, and enhanced performance.

Innovative adjustable belt guide wheel, permits a convenient method to change the belt tension by launching or tightening up the screw. The screw is used to preserve optimum belt tension over time.

The One Way Bearing is made utilizing bearing take and after heat treatment the firmness is HRC50-55. This bigger bearing has a greater load bring capacity which lowers the loss of momentum and enhances the fficiency, speed, and smoothness of the primary rotor. The new primary equipment case and all-metal main wheel transmission system is an efficient design to provide the supreme performance.

Landing skid is slanted 5 degrees forward to improve crashworthiness.

Newly designed vertical tail servo mount to improve CG while increasing the responsiveness of 3D flight.

A wider Tail Boom to enhances the torsional strength. Carbon Fiber Tail Control Rod is useful and enhances the helicopters tail control.

Designed utilizing a proprietary material integration innovation which develops a unique look and enhances the Vertical Stabilizer's stiffness.

The recently designed double point supported tail control assembly provides slop complimentary efficiency while improving rudder resolution and precision.

The new tail rotor holder design consists of thrust bearings which increases sturdiness, as well as considerably improving the accuracy and effectiveness of the tail efficiency when utilizing 69 size Tail Blades.

Standard equipment

?RCE-BL50X 50A Brushless ESC X 1
?470MX Brushless Motor(1800KV) X 1

Specification

?Length: 755mm
?Height: 210mm
?Width: 108mm
?Main Blade Length: 380mm
?Main Rotor Diameter: 850mm
?Tail Rotor Diameter: 181mm
?Motor Pinion Equipment: 11T
?Main Drive Equipment: 121T
?Main Drive Sheave: 56T
?Tail Drive Equipment: 15T
?Drive Equipment Ratio: 11:1:3.73
?Weight(w/o battery): 860gAccessories

?T-REX 470L DOMINATOR Set x 1
?380 Carbon Fiber Blades x 1set
?69 Tail Blade x1set
?470MX Brushless Motor(1800KV) x 1
?RCE-BL50X 50A Brushless ESC x 1

Radio transmitter and electronic equipment needed for assembly:
1.Transmitter(6-channel or more,helicopter system)
2.Receiver(6-channel or more)
3.Pitch gauge or Digital Pitch Gauge
4.6S Li-Po 1400~1900mAh battery x 1
5.CCPM Servo X 3
6.Tail Servo X 1
7.Flybarless System x 1