Align T-REX 470LM KIT (w/ Motor and ESC)

Following the release of the T-REX 450L, which presented an ingenious design and came geared up with high-end electronic devices. Align's the majority of expected helicopter release in 2016 the T-REX 470L is born. No matter whether you are a beginner or an expert, the brand name brand-new T-REX 470L will give you the brand-new flying feel again.

470EFL Main Rotor Head supplies exceptional flight stability and offers a lower CG design to minimize flying resistance while supplying a more rigid and quick rotor head response. To improve the strength and durability of the main and feathering shaft the 470 main shaft external measurement was increased from Ø5mm to Ø6mm, while the feathering shaft external measurement was increased from Ø4mm to Ø5mm. The 470L has adopt a high standard 1.2mm 3K carbon fiber main frame and a larger body design which increases the size of the battery compartment allowing the usage of bigger capacity battery. The 470L uses a high efficient belt drive assembly design with an ingenious adjustable belt guide sheave, supplying a hassle-free way to change the belt tension by releasing or tightening up the screw. This screw is utilized to maintain optimum belt tension enhancing the life of the belt and reducing preserves costs. The landing skid is tilted 5 degrees forward to improve crashworthiness and makes T-REX470L more progressive and dynamic.

The T-REX 470L is geared up with the large external size 470MX motor (1800KV) which is extremely efficient supplying exceptional power, excellent torque, improved existing draw, and a lower operating temperature level which are excellent improvements as compared with the 460MX motor.

Extended 380mm main blades efficiently improve the flying stability and power efficiency. The brand-new crafted airfoil design efficiently reduces turbulence at the end of the main blades,this saves power consumption throughout extreme 3D flight. New 69 size tail blades are longer in length and deal exceptional tail holding efficiency, even throughout requiring 3D flight.

Brand New 470EFL Main Rotor Head supplies exceptional flight stability and offers a lower CG design to minimize flying resistance while supplying a more rigid and quick rotor head response. Brand New 470 Main Shaft and Feathering Shaft: Main Shaft external measurement increased from Ø5mm to Ø6mm, while the Feathering Shaft external measurement increased from Ø4mm to Ø5mm,efficiently strengthening the Main and Feathering Shaft while enhancing durability.

New 470MX motor functions; high efficiency, exceptional power, excellent torque, low existing draw, and a low operating temperature level. The 470MX is capable of preserving consistent torque and head speed through continuous 3D maneuvers. 470MX motor is developed for 3D flight.

New Swashplate design with no slop delivering an exact and precise controlled flight.

Brand brand-new CNC metal support plate and brace compare to frame mounting bolt efficiently increase the torsional stength of main frame, under extreme 3D maneuver, you can highly feel its strong support from its structure.

Carbon fiber side frame plates are produced using a proprietary composite material integration technology which integrates the battery mounting rails into the frame. This special usage of open areas within the frame creates a stiff frame and is aesthetically pleasing.

An additional 3rd main shaft bearing block increases the strength of the main frame while enhancing 3D flight.

Brand brand-new locking battery tray which uses integrated mounting rails inside the frames to simplify insertion / removal of battery while supplying defense for the battery.

Specially developed for T-REX 470 supplying higher currency output and assistance for high voltage servos with an internal BEC output from 5V to 8.4V which can be set up based on servo specification.

DS350M HV Cyclic and DS455 HV Rudder servos support as much as 8.4V for exceptional responsiveness, extreme torque, and improved performance.

Innovative adjustable belt guide sheave, enables a hassle-free way to change the belt tension by releasing or tightening up the screw. The screw is utilized to maintain optimum belt tension over time.

The One Method Bearing is produced using bearing steal and after heat treatment the hardness is HRC50-55. This bigger bearing has a greater load bring capacity which reduces the loss of momentum and enhances the fficiency, speed, and smoothness of the main rotor. The brand-new main equipment case and all-metal central sheave transmission system is an effective design to deliver the supreme performance.

Landing skid is tilted 5 degrees forward to improve crashworthiness.

Newly developed vertical tail servo mount to improve CG while increasing the responsiveness of 3D flight.

A wider Tail Boom to enhances the torsional strength. Carbon Fiber Tail Control Rod is useful and enhances the helicopters tail control.

Designed using a proprietary material integration technology which creates a unique appearance and enhances the Vertical Stabilizer's stiffness.

The newly developed dual point supported tail control assembly delivers slop totally free efficiency while enhancing rudder resolution and precision.

The brand-new tail rotor holder design consists of thrust bearings which increases durability, as well as considerably enhancing the accuracy and efficiency of the tail efficiency when using 69 size Tail Blades.

Standard devices

?RCE-BL50X 50A Brushless ESC X 1
?470MX Brushless Motor(1800KV) X 1

Specification

?Length: 755mm
?Height: 210mm
?Width: 108mm
?Main Blade Length: 380mm
?Main Rotor Size: 850mm
?Tail Rotor Size: 181mm
?Motor Pinion Equipment: 11T
?Main Drive Equipment: 121T
?Main Drive Sheave: 56T
?Tail Own Equipment: 15T
?Own Equipment Ratio: 11:1:3.73
?Weight(w/o battery): 860gAccessories

?T-REX 470L BOSS Set x 1
?380 Carbon Fiber Blades x 1set
?69 Tail Blade x1set
?470MX Brushless Motor(1800KV) x 1
?RCE-BL50X 50A Brushless ESC x 1

Radio transmitter and electronic devices required for assembly:
1.Transmitter(6-channel or more,helicopter system)
2.Receiver(6-channel or more)
3.Pitch gauge or Digital Pitch Gauge
4.6S Li-Po 1400~1900mAh battery x 1
5.CCPM Servo X 3
6.Tail Servo X 1
7.Flybarless System x 1