Align T-REX 470LM KIT (w/ Motor and ESC)

Following the release of the T-REX 450L, which presented an innovative design and came geared up with high-end electronic equipment. Align's many anticipated helicopter release in 2016 the T-REX 470L is born. No matter whether you are a newbie or an expert, the brand name brand-new T-REX 470L will give you the brand-new flying feel again.

470EFL Main Rotor Head offers superior flight stability and provides a lower CG design to minimize flying resistance while supplying a more rigid and quick rotor head response. To enhance the strength and durability of the main and feathering shaft the 470 main shaft external dimension was increased from Ø5mm to Ø6mm, while the feathering shaft external dimension was increased from Ø4mm to Ø5mm. The 470L has embrace a high basic 1.2mm 3K carbon fiber main frame and a wider body design which increases the size of the battery compartment enabling the usage of larger capacity battery. The 470L utilizes a high efficient belt drive assembly design with an innovative adjustable belt guide sheave, supplying a convenient way to adjust the belt tension by launching or tightening the screw. This screw is used to maintain optimum belt tension enhancing the life of the belt and lowering keeps expenses. The landing skid is slanted 5 degrees forward to enhance crashworthiness and makes T-REX470L more avant-garde and dynamic.

The T-REX 470L is geared up with the large external size 470MX motor (1800KV) which is extremely efficient supplying superior power, excellent torque, improved existing draw, and a lower operating temperature level which are excellent enhancements as compared to the 460MX motor.

Extended 380mm main blades efficiently enhance the flying stability and power efficiency. The brand-new engineered airfoil design efficiently minimizes turbulence at the end of the main blades,this conserves power intake during extreme 3D flight. New 69 size tail blades are longer in length and offer superior tail holding efficiency, even during demanding 3D flight.

Brand New 470EFL Main Rotor Head offers superior flight stability and provides a lower CG design to minimize flying resistance while supplying a more rigid and quick rotor head response. Brand New 470 Main Shaft and Feathering Shaft: Main Shaft external dimension increased from Ø5mm to Ø6mm, while the Feathering Shaft external dimension increased from Ø4mm to Ø5mm,efficiently enhancing the Main and Feathering Shaft while enhancing durability.

New 470MX motor features; high effectiveness, superior power, excellent torque, low existing draw, and a low operating temperature level. The 470MX is capable of preserving constant torque and head speed through continuous 3D maneuvers. 470MX motor is created for 3D flight.

New Swashplate design with no slop delivering an exact and precise regulated flight.

Brand brand-new CNC metal support plate and brace compare with frame mounting bolt efficiently increase the torsional stength of main frame, under extreme 3D maneuver, you can strongly feel its strong support from its structure.

Carbon fiber side frame plates are produced using a proprietary composite material combination technology which integrates the battery mounting rails into the frame. This distinct usage of open areas within the frame develops a stiff frame and is visually pleasing.

An extra 3rd main shaft bearing block increases the strength of the main frame while enhancing 3D flight.

Brand brand-new locking battery tray which utilizes incorporated mounting rails inside the frames to streamline insertion / removal of battery while supplying security for the battery.

Specially created for T-REX 470 supplying greater currency output and assistance for high voltage servos with an internal BEC output from 5V to 8.4V which can be set up based upon servo specification.

DS350M HV Cyclic and DS455 HV Rudder servos support as much as 8.4V for superior responsiveness, extreme torque, and improved performance.

Innovative adjustable belt guide sheave, permits a convenient way to adjust the belt tension by launching or tightening the screw. The screw is used to maintain optimum belt tension over time.

The One Way Bearing is produced using bearing take and after heat treatment the solidity is HRC50-55. This larger bearing has a higher load carry capacity which minimizes the loss of momentum and improves the fficiency, speed, and smoothness of the main rotor. The brand-new main gear case and all-metal main sheave transmission system is an efficient design to provide the ultimate performance.

Landing skid is slanted 5 degrees forward to enhance crashworthiness.

Newly created vertical tail servo install to enhance CG while increasing the responsiveness of 3D flight.

A wider Tail Boom to improves the torsional strength. Carbon Fiber Tail Control Rod is practical and improves the helicopters tail control.

Designed using a proprietary material combination technology which develops a unique appearance and improves the Vertical Stabilizer's stiffness.

The freshly created double point supported tail control assembly delivers slop complimentary efficiency while enhancing rudder resolution and precision.

The brand-new tail rotor holder design includes thrust bearings which increases durability, in addition to significantly enhancing the accuracy and effectiveness of the tail efficiency when using 69 size Tail Blades.

Standard equipment

?RCE-BL50X 50A Brushless ESC X 1
?470MX Brushless Motor(1800KV) X 1

Spec

?Length: 755mm
?Height: 210mm
?Width: 108mm
?Main Blade Length: 380mm
?Main Rotor Diameter: 850mm
?Tail Rotor Diameter: 181mm
?Motor Pinion Equipment: 11T
?Main Drive Equipment: 121T
?Main Drive Pulley-block: 56T
?Tail Drive Equipment: 15T
?Drive Equipment Ratio: 11:1:3.73
?Weight(w/o battery): 860gAccessories

?T-REX 470L DOMINATOR Set x 1
?380 Carbon Fiber Blades x 1set
?69 Tail Blade x1set
?470MX Brushless Motor(1800KV) x 1
?RCE-BL50X 50A Brushless ESC x 1

Radio transmitter and electronic equipment needed for assembly:
1.Transmitter(6-channel or more,helicopter system)
2.Receiver(6-channel or more)
3.Pitch gauge or Digital Pitch Gauge
4.6S Li-Po 1400~1900mAh battery x 1
5.CCPM Servo X 3
6.Tail Servo X 1
7.Flybarless System x 1