Align Hook and Loop Tape/600 Use

Usage Hook and Loop Tape, tape the Hook side(hooked) on the battery mounting plate and the Loop side(fuzzy) on the battery to repair the battery and avoid any slip.
Specifications:
Hook and Loop Tape- Hook side (hooked) x 4(85x44mm)
Hook and Loop Tape- Loop side (fuzzy) x 6(85x44mm)

Get this product to boost the one you are reading around.

LIPO 450mAh 7.4V 30C- Blade 130X

* True 5C Charge Rates
* Myriads of Voltages, Capacities & C Scores
* 15C / 25C / 35C / 45C / 65C Layouts for High Power Demands
* Big Multi Rotor Loads Fit Particularly for Multi Rotor Demands
* Numerous Plane Battery Applications Readily available
* Transmitter & Receiver Load Options
* Big AWG Wiring for Maximum Power Applications
* Industry Basic JST/XH Balance Taps
* 90 Day Producer Warranty from Point of Consumer Purchase

Specs:
Voltage: 7.4V
Cell Count: 2S
Capacity: 450 mAh
Discharge Rate: 30C
Charge Rate: 5C
Measurements: 54 x 30 x 9 (LxWxH)
Weight: 29g
Balance Tap: Stock Port

This product praises the above gone over product.

Torque Tube

Usage for T-REX 550E.

Specs:
Torque tube x 1
Bearing MR148ZZ x 1(Φ8xΦ14x4mm)

This product is often purchased with the above stated product.

Hook & Loop Fastening Tape

Specs:
Hook & Loop attaching tape x 2 (20x360mm)

You will enjoy this product if you have the product above pointed out.

Hook and Loop Tape/450 Use

Specs:
Usage Hook and Loop Tape, tape the Hook side(hooked) on the battery mounting plate and the Loop side(fuzzy) on the battery to repair the battery and avoid any slip.
Hook and Loop Tape- Hook side (hooked) x 4(54x28mm)
Hook and Loop Tape- Loop side (fuzzy) x 6(54x28mm)

Below is a terrific product that lots of others have actually purchased the very same time.

Metal Stabilizer Belt

Usage for T-REX 600/600 Nitro.

Specs:
Stabilizer install(Upper) x 1
Stabilizer install(Lower) x 1
3K carbon vertical stabilizer x 1
Socket collar screw x 2(M3x22mm)
Socket screw x 2(M3x8mm)
M3 specialty washer x 4(Φ3xΦ8x2mm)

Want an additional terrific product to enhance the above stated product?

Hook And Loop Tape

Specs:
Hook and loop tape x 2(15x250mm)
Hook and loop tape x 3(10x200mm)

The listed below product likewise pairs truly well with the product being gone over.

One-way Bearing

Usage for T-REX 550E/600/600 Nitro
Specs:
One-way bearing shaft HF1216 x 1(Φ12xΦ18x16mm)
INA Made in Germany

This product praises the above gone over product.

Main Frame Parts

Usage for T-REX 550E.

Specs:
600 Battery Mount x 1
550E Gyro Mount x 1
550E Rudder Servo Mount x 1

Lots of others have actually purchased this product along with the product that you are presently checking out.

Tail Boom

Make an application for T-REX 550E

Specifications:
Tail boom x 2(Φ20.3xΦ21.5x549mm)
Tail control guide x 2
Rudder control rod x 1(Φ1.96x575mm)
Ball Link x 2

You will enjoy this product if you have the product above pointed out.

M0.8 Torque Tube Front Drive Gear Set/34T

Usage for T-REX 600PRO/600EFL PRO/550E

Specifications:
600PRO Front drive gear assembly x 1
600PRO Short umbrella gear x 1
600PRO Long umbrella gear x 1

Below is an additional product that praises the product being gone over.

550 3G Carbon Fiber Blades

Usage for T-REX 550E Helicopter

Requirements:
Forming: In proportion wing
Length:550x50x6.7mm
Width:12mm
Shaft Size:4mm
Weight:Appro 210g/set

You will enjoy this product if you have the product above pointed out.

90 Carbon Fiber Tail Blade

Usage for T-REX 550E.

Specs:
Forming: In proportion wing
Length: 90mm
Width: 4.9mm
Shaft Size: 3mm
Weight: 9g/set