Align Ball Link

Usage for T-REX 500/600/600 Nitro.

Specifications:
Ball link-Black x 12
Elevator ball link x 1

Numerous others have actually bought this product in addition to the product that you are presently reading about.

M0.8 Torque Tube Front Drive Gear Set (34T)

This is an Align M0.8, 34 Tooth Torque Tube Front Drive Gear Set, and is intended for use with the Align T-Rex 550 V2 and 600 Pro helicopters.
Includes:
(1) Modulus: 0.8 Front drive gear assembly (4x4.5x51mm)
(1) Front umbrella gear (20T) (21.2x33.6mm)
(1) Tail umbrella gear (20T) (21.2x12.5mm)

Note: In order to utilize this torque tube drive gear set on a T-REX 550, the helicopter should be geared up with the slanted gear setup. To figure out if your helicopter utilizes slanted gears or straight-cut gears, observe the primary drive gear which will either have actually slanted or straight-cut teeth.



Numerous others have actually bought this product in addition to the product that you are presently reading about.

520 Carbon Fiber Blade Set (550E)

This is an optional Align 520mm Carbon Fiber Main Blade Set, and is intended for use with the Align T-Rex 550 helicopter.


Specs:

Forming: Symmetrical wing

Length: 520x48x6.5mm

Width: 12mm

Shaft Size: 4mm

Weight: 200g/set



This is a amazing enhancement to the product presently being reviewed.

6800ZZ Metal Rotor Holder Bearing Set (4)

This is a replacement Align 6800ZZ Metal Rotor Holder Bearing Set, and is intended for use with the Align T-Rex 700 Helicopter. 
Consists of:

(4) 10x19x5mm Metal Protected Bearings





Below is one more product that praises the product being reviewed.



The new DELUXE swashplate leveler is created to level the swashplate without eyeballing and guessing, enabling you to dial in the helicopter with excellent precision & precision. This swashplate leveler is utilized for T-REX 700 Nitro helicopters, and is particularly created for the swashplate of the Trex 700N. Due to its heavy weight, this new version is created with a leading finger rest, in addition to an ergonomic handle to falcilitate the leveling job.

The NEW DELUXE swashplate leveler is made of airplane aluminum 6061-T6, and is CNC machined with the greatest tolerances to remove any play between the primary shaft and swashplate leveler, which can cause an incorrectly leveled swashplate. The NEW DELUXE swashplate leveler is likewise anodized in silver to avoid corrosion.

Designed to work with a 12mm Main Shaft.

Designed in the USA.
Specifications:

Length: 38mm
Main Shaft hole: 12mm

Click on this link to download manual !

This is a amazing enhancement to the product presently being reviewed.

Servo line Color Black and Red

Aiming to clean up the look of your helicopter, airplane of RC automobile & protect your servo lines from chaffing? Servo Line Covering is an easy way to protect your servo wires, including a clean, aesthetic planning to your RC machine, and can be installed in a matter of minutes. Pick from our exciting line of varied colors to include an entire make over to your RC machine!

Included In Package:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply remove your servo(s) from the receiver, determine the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal inside. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and slowly inching the covering over the terminal, and pressing the terminal forward.

Once your servo wire is covered, cut off a proper sized piece of the consisted of heat diminish, and slide it over the covering till it is flush with the servo itself. Heat the diminish wrap with a soldering iron or heat gun to diminish it down around the covering, hence offering you a flush, tight fit over the formerly frayed servo covering. Do the very same with completion of your servo wire, taking care to leave the terminal bare so it can easily connected into your receiver. Also, be sure to bear in mind of the servo wire polarity if you cover the full wire – this will ensure that you will understand what direction to plug your servo terminal into your receiver.