Align Ball Link

Use for T-REX 500/600/600 Nitro.

Specifications:
Ball link-Black x 12
Elevator ball link x 1

Many others have acquired this thing together with the thing that you are currently reading about.

M0.8 Torque Tube Front Drive Gear Set (34T)

This is an Align M0.8, 34 Tooth Torque Tube Front Drive Gear Set, and is intended for use with the Align T-Rex 550 V2 and 600 Pro helicopters.
Includes:
(1) Modulus: 0.8 Front drive gear assembly (4x4.5x51mm)
(1) Front umbrella gear (20T) (21.2x33.6mm)
(1) Tail umbrella gear (20T) (21.2x12.5mm)

Note: In order to utilize this torque tube drive gear set on a T-REX 550, the helicopter must be equipped with the slanted gear setup. To figure out if your helicopter uses slanted gears or straight-cut gears, observe the main drive gear which will either have actually slanted or straight-cut teeth.



Many others have acquired this thing together with the thing that you are currently reading about.

520 Carbon Fiber Blade Set (550E)

This is an optional Align 520mm Carbon Fiber Main Blade Set, and is intended for use with the Align T-Rex 550 helicopter.


Requirements:

Shape: Symmetrical wing

Length: 520x48x6.5mm

Width: 12mm

Shaft Diameter: 4mm

Weight: 200g/set



This is a wonderful addition to the thing currently being reviewed.

6800ZZ Metal Rotor Holder Bearing Set (4)

This is a replacement Align 6800ZZ Metal Rotor Holder Bearing Set, and is intended for use with the Align T-Rex 700 Helicopter. 
Includes:

(4) 10x19x5mm Metal Shielded Bearings





Here is one more thing that praises the thing being reviewed.



The brand-new DELUXE swashplate leveler is created to level the swashplate without eyeballing and guessing, permitting you to call in the helicopter with excellent precision & accuracy. This swashplate leveler is utilized for T-REX 700 Nitro helicopters, and is particularly created for the swashplate of the Trex 700N. Due to its heavy weight, this brand-new version is created with a top finger rest, together with an ergonomic deal with to falcilitate the leveling job.

The NEW DELUXE swashplate leveler is made from aircraft aluminum 6061-T6, and is CNC machined with the highest tolerances to get rid of any play between the main shaft and swashplate leveler, which can cause an incorrectly leveled swashplate. The NEW DELUXE swashplate leveler is likewise anodized in silver to prevent corrosion.

Designed to work with a 12mm Main Shaft.

Designed in the USA.
Specifications:

Length: 38mm
Main Shaft hole: 12mm

Click here to download handbook !

This is a wonderful addition to the thing currently being reviewed.

Servo line Color Black and Red

Seeking to clean up the appearance of your helicopter, airplane of RC vehicle & safeguard your servo lines from chaffing? Servo Line Covering is an easy method to safeguard your servo wires, adding a clean, visual aim to your RC device, and can be installed in a matter of minutes. Select from our amazing line of varied colors to add a whole new look to your RC machine!

Included In Plan:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply remove your servo(s) from the receiver, determine the length of covering you will require for your servo wire(s), and open one end of the covering and insert the servo terminal inside. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off a proper sized piece of the consisted of heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat weapon to shrink it down around the covering, hence providing you a flush, tight fit over the previously frayed servo covering. Do the exact same with completion of your servo wire, being careful to leave the terminal bare so it can easily plug into your receiver. Likewise, make certain to remember of the servo wire polarity if you cover the complete wire – this will make sure that you will know exactly what instructions to plug your servo terminal into your receiver.