Align Ball Link

Use for T-REX 500/600/600 Nitro.

Specifications:
Ball link-Black x 12
Elevator ball link x 1

Lots of others have actually bought this thing along with the thing that you are presently reviewing.

M0.8 Torque Tube Front Drive Gear Set (34T)

This is an Align M0.8, 34 Tooth Torque Tube Front Drive Gear Set, and is intended for use with the Align T-Rex 550 V2 and 600 Pro helicopters.
Includes:
(1) Modulus: 0.8 Front drive gear assembly (4x4.5x51mm)
(1) Front umbrella gear (20T) (21.2x33.6mm)
(1) Tail umbrella gear (20T) (21.2x12.5mm)

Note: In order to utilize this torque tube drive gear set on a T-REX 550, the helicopter must be equipped with the inclined gear setup. To figure out if your helicopter uses inclined gears or straight-cut gears, observe the primary drive gear which will either have actually inclined or straight-cut teeth.



Lots of others have actually bought this thing along with the thing that you are presently reviewing.

520 Carbon Fiber Blade Set (550E)

This is an optional Align 520mm Carbon Fiber Main Blade Set, and is intended for use with the Align T-Rex 550 helicopter.


Specs:

Shape: Balanced wing

Length: 520x48x6.5mm

Width: 12mm

Shaft Size: 4mm

Weight: 200g/set



This is a amazing enhancement to the thing presently being talked about.

6800ZZ Metal Rotor Holder Bearing Set (4)

This is a replacement Align 6800ZZ Metal Rotor Holder Bearing Set, and is intended for use with the Align T-Rex 700 Helicopter. 
Includes:

(4) 10x19x5mm Metal Protected Bearings





Right here is an additional thing that compliments the thing being talked about.



The new DELUXE swashplate leveler is designed to level the swashplate without eyeballing and guessing, permitting you to dial in the helicopter with terrific accuracy & precision. This swashplate leveler is utilized for T-REX 700 Nitro helicopters, and is specifically designed for the swashplate of the Trex 700N. Due to its heavy weight, this new variation is designed with a leading finger rest, in addition to an ergonomic deal with to falcilitate the leveling job.

The NEW DELUXE swashplate leveler is made from aircraft aluminum 6061-T6, and is CNC machined with the greatest tolerances to get rid of any play in between the primary shaft and swashplate leveler, which can result in an improperly leveled swashplate. The NEW DELUXE swashplate leveler is also anodized in silver to prevent corrosion.

Designed to work with a 12mm Main Shaft.

Designed in the USA.
Specifications:

Length: 38mm
Main Shaft hole: 12mm

Click here to download manual !

This is a amazing enhancement to the thing presently being talked about.

Servo line Color Black and Red

Seeking to clean up the look of your helicopter, airplane of RC automobile & safeguard your servo lines from chaffing? Servo Line Covering is an easy way to safeguard your servo wires, including a clean, visual seek to your RC device, and can be set up in a matter of minutes. Choose from our amazing line of varied colors to include an entire new look to your RC machine!

Included In Package:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply remove your servo(s) from the receiver, measure the length of covering you will need for your servo wire(s), and open one end of the covering and insert the servo terminal within. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off a suitable sized piece of the consisted of heat diminish, and slide it over the covering till it is flush with the servo itself. Heat the diminish wrap with a soldering iron or heat weapon to diminish it down around the covering, thus providing you a flush, tight fit over the previously frayed servo covering. Do the same with completion of your servo wire, bewaring to leave the terminal bare so it can easily connected into your receiver. Also, make certain to bear in mind of the servo wire polarity if you cover the full wire – this will guarantee that you will understand exactly what instructions to plug your servo terminal into your receiver.