Align Ball Link

Use for T-REX 500/600/600 Nitro.

Specifications:
Ball link-Black x 12
Elevator ball link x 1

Numerous others have actually purchased this item in addition to the item that you are presently reviewing.

M0.8 Torque Tube Front Drive Gear Set (34T)

This is an Align M0.8, 34 Tooth Torque Tube Front Drive Gear Set, and is meant for use with the Align T-Rex 550 V2 and 600 Pro helicopters.
Includes:
(1) Modulus: 0.8 Front drive gear assembly (4x4.5x51mm)
(1) Front umbrella gear (20T) (21.2x33.6mm)
(1) Tail umbrella gear (20T) (21.2x12.5mm)

Note: In order to utilize this torque tube drive gear set on a T-REX 550, the helicopter should be geared up with the slanted gear setup. To determine if your helicopter utilizes slanted gears or straight-cut gears, observe the main drive gear which will either have slanted or straight-cut teeth.



Numerous others have actually purchased this item in addition to the item that you are presently reviewing.

520 Carbon Fiber Blade Set (550E)

This is an optional Align 520mm Carbon Fiber Main Blade Set, and is meant for use with the Align T-Rex 550 helicopter.


Requirements:

Forming: Symmetrical wing

Length: 520x48x6.5mm

Width: 12mm

Shaft Size: 4mm

Weight: 200g/set



This is a superb enhancement to the item presently being talked about.

6800ZZ Metal Rotor Holder Bearing Set (4)

This is a replacement Align 6800ZZ Metal Rotor Holder Bearing Set, and is meant for use with the Align T-Rex 700 Helicopter. 
Consists of:

(4) 10x19x5mm Metal Shielded Bearings





Here is another item that praises the item being talked about.



The brand-new DELUXE swashplate leveler is developed to level the swashplate without eyeballing and thinking, allowing you to dial in the helicopter with fantastic accuracy & accuracy. This swashplate leveler is used for T-REX 700 Nitro helicopters, and is specifically developed for the swashplate of the Trex 700N. Due to its heavy weight, this brand-new version is developed with a leading finger rest, along with an ergonomic handle to falcilitate the leveling job.

The NEW DELUXE swashplate leveler is made of aircraft aluminum 6061-T6, and is CNC machined with the highest tolerances to remove any play in between the main shaft and swashplate leveler, which can lead to an improperly leveled swashplate. The NEW DELUXE swashplate leveler is likewise anodized in silver to avoid corrosion.

Designed to deal with a 12mm Main Shaft.

Designed in the USA.
Specifications:

Length: 38mm
Main Shaft hole: 12mm

Click on this link to download manual !

This is a superb enhancement to the item presently being talked about.

Servo line Color Black and Red

Looking to tidy up the appearance of your helicopter, aircraft of RC automobile & protect your servo lines from chaffing? Servo Line Covering is a simple method to protect your servo wires, adding a tidy, aesthetic aim to your RC machine, and can be set up in a matter of minutes. Pick from our exciting line of varied colors to include a whole makeover to your RC machine!

Included In Plan:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Set up Servo Line Covering?

Simply remove your servo(s) from the receiver, measure the length of covering you will require for your servo wire(s), and open one end of the covering and place the servo terminal inside. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and slowly inching the covering over the terminal, and pushing the terminal forward.

Once your servo wire is covered, cut off a suitable sized piece of the consisted of heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat gun to shrink it down around the covering, thus providing you a flush, tight fit over the previously frayed servo covering. Do the exact same with completion of your servo wire, bewaring to leave the terminal bare so it can quickly connected into your receiver. Also, be sure to keep in mind of the servo wire polarity if you cover the complete wire – this will guarantee that you will know what direction to plug your servo terminal into your receiver.