Align Ball Link

Usage for T-REX 500/600/600 Nitro.

Specifications:
Ball link-Black x 12
Elevator ball link x 1

Many others have gotten this thing along with the thing that you are currently checking out.

M0.8 Torque Tube Front Drive Gear Set (34T)

This is an Align M0.8, 34 Tooth Torque Tube Front Drive Gear Set, and is intended for usage with the Align T-Rex 550 V2 and 600 Pro helicopters.
Includes:
(1) Modulus: 0.8 Front drive gear assembly (4x4.5x51mm)
(1) Front umbrella gear (20T) (21.2x33.6mm)
(1) Tail umbrella gear (20T) (21.2x12.5mm)

Note: In order to utilize this torque tube drive gear set on a T-REX 550, the helicopter needs to be equipped with the inclined gear setup. To identify if your helicopter uses inclined gears or straight-cut gears, observe the primary drive gear which will either have actually inclined or straight-cut teeth.



Many others have gotten this thing along with the thing that you are currently checking out.

520 Carbon Fiber Blade Set (550E)

This is an optional Align 520mm Carbon Fiber Main Blade Set, and is intended for usage with the Align T-Rex 550 helicopter.


Requirements:

Forming: Balanced wing

Length: 520x48x6.5mm

Width: 12mm

Shaft Size: 4mm

Weight: 200g/set



This is a amazing enhancement to the thing currently being gone over.

6800ZZ Metal Rotor Holder Bearing Set (4)

This is a replacement Align 6800ZZ Metal Rotor Holder Bearing Set, and is intended for usage with the Align T-Rex 700 Helicopter. 
Includes:

(4) 10x19x5mm Metal Shielded Bearings





Right here is an additional thing that compliments the thing being gone over.



The new DELUXE swashplate leveler is created to level the swashplate without eyeballing and thinking, allowing you to dial in the helicopter with excellent precision & precision. This swashplate leveler is utilized for T-REX 700 Nitro helicopters, and is particularly created for the swashplate of the Trex 700N. Due to its heavy weight, this new variation is created with a top finger rest, along with an ergonomic deal with to falcilitate the leveling job.

The NEW DELUXE swashplate leveler is made from airplane aluminum 6061-T6, and is CNC machined with the highest tolerances to remove any play between the primary shaft and swashplate leveler, which can cause an incorrectly leveled swashplate. The NEW DELUXE swashplate leveler is also anodized in silver to avoid corrosion.

Designed to work with a 12mm Main Shaft.

Designed in the USA.
Specifications:

Length: 38mm
Main Shaft hole: 12mm

Click here to download manual !

This is a amazing enhancement to the thing currently being gone over.

Servo line Color Black and Red

Wanting to tidy up the appearance of your helicopter, aircraft of RC automobile & secure your servo lines from chaffing? Servo Line Covering is a simple way to secure your servo wires, including a clean, visual seek to your RC device, and can be installed in a matter of minutes. Choose from our exciting line of varied colors to add a whole make over to your RC machine!

Included In Bundle:

(1) 1M (3.28 ft.) Servo Line Covering

(1) 9 in. Heat Shrink Wrap

How Do I Install Servo Line Covering?

Simply remove your servo(s) from the receiver, determine the length of covering you will need for your servo wire(s), and open one end of the covering and place the servo terminal within. It works best to “inch worm” your servo wire by holding the terminal inside the servo covering, and gradually inching the covering over the terminal, and pressing the terminal forward.

Once your servo wire is covered, cut off an appropriate sized piece of the consisted of heat shrink, and slide it over the covering till it is flush with the servo itself. Heat the shrink wrap with a soldering iron or heat weapon to shrink it down around the covering, therefore offering you a flush, tight fit over the previously frayed servo covering. Do the same with completion of your servo wire, bewaring to leave the terminal bare so it can easily plug into your receiver. Also, be sure to take note of the servo wire polarity if you cover the full wire – this will make sure that you will understand exactly what direction to plug your servo terminal into your receiver.